Engineering Plastics: The Abbreviations, and What Actually Limits a Machined Part
An engineer who machines metal reliably will select plastic badly on the first few parts, and the reason is that the controlling variables are different. Hardness barely matters. What decides whether a plastic part works is how much water it absorbs, how much it expands when warm, how much it creeps under a load held for a year, and whether a sharp corner will start a crack.
The abbreviations are the first obstacle and they are the easy one. PA66, PBT, POM, PPS: each is a polymer family, and within each family there is a further layer of modification — glass filled, flame retardant, heat stabilised, wear modified — that changes the properties more than changing the base polymer would. A 30% glass-filled PA66 is not a slightly better PA66; it is a different material with a different machining behaviour.
Four Variables That Decide a Plastic Part
| Variable | What happens | Where it bites |
|---|---|---|
| Moisture absorption | Polyamides take up water into the polymer structure, which swells the part and drops its stiffness and strength. Unfilled PA66 reaches roughly 2.5% at 23 °C and 50% relative humidity, and considerably more when immersed. | A part measured dry and installed humid is out of tolerance; a tight fit becomes an interference fit after a season in service. |
| Thermal expansion | Unfilled engineering plastics expand about five to ten times as much as steel per degree. Glass filling reduces this substantially but does not remove it. | A 100 mm plastic part moves several tenths of a millimetre over a 40 °C swing; a press fit designed with metal habits will loosen or seize. |
| Creep | Under sustained load the part continues to deform with time, even well below yield. | Bolted joints lose preload, seals lose contact pressure, and a bushing that was a light press fit becomes loose. |
| Notch sensitivity | A sharp internal corner concentrates stress and plastics have limited ability to redistribute it. | Thread roots, keyways, grooves and sharp shoulders crack under impact that the same geometry in metal would survive. |
How to Read the Abbreviation
The base abbreviation tells you the polymer family and therefore the general property envelope. The suffix or the compound name tells you what was added, and the addition usually matters more.
- GF or a number — glass fibre, usually 15%, 30% or 50%. Raises stiffness and strength, reduces expansion and creep, and makes the material abrasive to machine and less pleasant to finish.
- FR — flame retardant. Usually halogenated or halogen-free phosphorus or nitrogen systems. Flame-retardant grades can be more corrosive to tooling and more sensitive to moisture.
- Heat stabilised — a package that slows thermal ageing, extending service temperature by tens of degrees without changing the base polymer.
- Wear or lubricated — PTFE, silicone oil or graphite added to lower friction. These grades are chosen for sliding contact, not for structural use.
- Conductive or antistatic — carbon black, carbon fibre or metal filler. Carbon fibre raises stiffness as well as conductivity; carbon black mainly changes the electrical behaviour.
- Impact modified — elastomer addition, usually at the cost of stiffness and sometimes of UV stability.
The Four Groups
| Group | Character | Materials | Typical role |
|---|---|---|---|
| Commodity | Low cost, adequate for non-structural parts | PP, ABS | Covers, housings, brackets, low-load parts |
| Engineering | Balanced mechanical properties, dimensionally usable | PA66, PA46, POM, PBT, PET, PC, PC/ABS | The bulk of machined functional parts |
| High performance | High temperature, chemical resistance, dimensional stability | PPS, LCP, PEEK | Parts that see heat, solvents or tight tolerance over temperature |
| Thermoset composite | Cannot be remelted; formed rather than machined from stock | BMC, DMC, SMC | Electrical housings, structural panels; usually moulded, occasionally trimmed |
The Materials
| Abbreviation | Full name | Chosen for | Main limitation | Typical machined part |
|---|---|---|---|---|
| PA66 | Polyamide 66 (nylon 66) | Strength, toughness, wear resistance; the most modified family in common use | Moisture absorption changes dimensions, strength and electrical properties | Bushes, rollers, wear pads, insulators, brackets |
| PA46 | Polyamide 46 | Higher heat resistance than PA66 with good fatigue strength | Still moisture sensitive; higher processing temperature | Parts in small engines and under-bonnet assemblies |
| PBT | Polybutylene terephthalate | Low moisture uptake, dimensional stability, good electrical properties, mature flame-retardant systems | Notch sensitive; hydrolysis risk in hot water | Connector bodies, coil formers, sensor housings |
| PET | Polyethylene terephthalate | Stiffness, dimensional stability, low moisture; strong in film form | Slower crystallisation than PBT in moulding; limited as a machined structural material | Insulating components, food-contact parts |
| PC | Polycarbonate | Transparency, impact strength, toughness | Poor scratch and chemical resistance; stress cracking with solvents and cleaners | Windows, guards, transparent covers, impact-resistant housings |
| ABS | Acrylonitrile butadiene styrene | Processing ease, appearance, toughness, low cost | Not a high-temperature material; needs modification for flame retardance | Covers, knobs, housings, appearance parts |
| PC/ABS | Polycarbonate / ABS blend | Combines PC impact strength with ABS processing and appearance | Property depends heavily on the blend ratio and grade | Housings, bezels, internal structural covers |
| POM | Polyoxymethylene (acetal) | Wear resistance, self-lubrication, dimensional stability, machinability | Not a high-temperature or electrically insulating material; degrades in strong acids | Gears, cams, bushes, rollers, conveyor parts, spacers |
| PPS | Polyphenylene sulfide | High temperature, chemical resistance, inherent flame retardance, dimensional stability | Brittle compared with PA or POM; higher cost | Pump parts, valve bodies, chemical-contact components |
| LCP | Liquid crystal polymer | High flow for thin walls, high temperature, excellent dimensional stability | Anisotropic properties; weak weld lines; costly | Thin-wall connectors, precision small parts, electronic housings |
| PEEK | Polyether ether ketone | High continuous temperature, strength, wear and chemical resistance together | Cost; requires high processing temperature | Semiconductor parts, medical and aerospace components, high-temperature seals |
| PP | Polypropylene | Low density, chemical resistance, low cost | Limited stiffness, heat resistance and dimensional stability | Chemical tanks, lids, low-load covers |
| BMC / DMC | Bulk / dough moulding compound | Thermoset with filler and glass; heat, flame and electrical performance | Cannot be remelted; machining is limited to trimming and finishing | Electrical enclosures, insulators, heavy-duty housings |
| SMC | Sheet moulding compound | Thermoset glass-reinforced sheet for larger parts; strength and dimensional stability | Surface finish and edge quality require care; not a machined-from-stock material | Large panels, structural covers, equipment housings |
What the Modifiers Cost You at the Machine
Glass filling is the most common and the most consequential. It raises stiffness, cuts thermal expansion and improves creep resistance, and it also turns the material abrasive, so tool life drops sharply and carbide becomes the practical minimum. Glass-filled grades also shrink anisotropically, which means a machined-from-stock part is fine but the same material moulded will not hold the same tolerances in flow and cross-flow directions.
Flame-retardant packages are the second. Halogenated systems can release corrosive species at machining and processing temperatures, and some FR grades are noticeably more moisture sensitive than the base polymer. Where the drawing specifies FR and the base grade is available, the FR grade is a different material and cannot be substituted quietly.
The practical consequence on a drawing is that "POM" or "PA66" alone is not a specification. It narrows the field to one family and leaves the property envelope wide open.
What Changes on the Shop Floor
- Stress relief before finishing. Extruded and moulded stock carries internal stress. Rough machine, anneal, then finish, or the part will move after the last cut.
- Moisture conditioning before measurement. A polyamide part measured immediately after machining is dry and will grow. Where the drawing specifies a tolerance on a PA part, the moisture condition at measurement has to be agreed, or the two parties will disagree about a conforming part.
- Clamping force. Plastics deflect under clamping pressure. A thin-wall part held hard in a chuck is round in the machine and oval on the bench.
- Sharp tools and clearance. A dull tool generates heat, and heat in plastic means smeared surfaces, built-up edge and dimensional drift rather than the wear pattern a metal machinist expects.
- Burr behaviour. Plastics burr by tearing rather than by shearing, and the burr is often attached more firmly than it looks. Deburring methods that work on metal can scratch or melt the surface.
- Coolant and cleaning. Some plastics absorb or are attacked by common coolants and solvents. PC in particular stress cracks in the presence of many cleaning agents.
The Three-Way Decision: POM, PA66 or PEEK
These three account for most machined plastic parts and the decision between them is usually simpler than the specification suggests.
| POM | PA66 | PEEK | |
|---|---|---|---|
| Choose when | The part slides, wears or needs stable dimensions at moderate temperature | The part needs toughness and impact resistance, or is heavily modified for a specific job | The part sees sustained high temperature, aggressive chemistry, or both |
| Do not choose when | The part runs hot, or needs electrical insulation, or sees strong acid | The tolerance is tight and the environment is humid | The cost cannot be justified by the service condition |
| Machining note | Machines cleanly; watch clamping distortion on thin sections | Machines cleanly but moves after machining as it takes up moisture | Machines cleanly; abrasive if glass or carbon filled |
Specifying Plastic on a Drawing
Three pieces of information remove almost all of the ambiguity.
- Family plus modification. "PA66-GF30-FR" rather than "nylon". Where a specific grade matters, name the supplier's trade designation, because two 30% glass-filled PA66 grades from different suppliers are not interchangeable in a tight tolerance.
- Condition at measurement. Dry as machined, or conditioned to a stated humidity. Without this, a tolerance on a polyamide is not a testable requirement.
- The service temperature and the chemical contact. Both narrow the family faster than any mechanical property table, and both are routinely omitted.
What to Put in an RFQ
- The material designation including modifiers, or the supplier trade name if the grade is critical.
- The stock form: rod, plate or tube, since property and stress condition differ between them.
- Whether a specific colour or opacity is required, and whether regrind is acceptable.
- The service temperature, the chemical contact and whether the part is a wear part.
- Whether the part will be measured dry or conditioned, and the tolerance basis that follows.
- Any food contact, medical or flame-retardance requirement, since these constrain the grade rather than the process.
Frequently Asked Questions
Why did a POM part come back oversize after a few weeks?
POM is dimensionally stable compared with the polyamides, so the usual cause is something else: residual stress from machining being relieved over time, or the part absorbing moisture in storage, or a measurement taken while the part was still warm from cutting. The sequence that avoids it is rough machine, stress relieve, finish machine, and measure after the part has settled at the specified condition.
Can nylon be used outdoors?
Standard PA66 degrades under UV and takes up moisture, so an outdoor part needs a stabilised grade and a design that tolerates dimensional change. Where the part is exposed and the tolerance is tight, a different family is usually the better answer, because no stabiliser package removes moisture absorption.
Is glass-filled plastic harder to machine than unfilled?
Considerably. The glass fibre is abrasive, so tool life falls sharply and carbide tooling becomes the practical minimum. Surface finish also suffers, because fibres at the cut surface tear rather than shear. The trade is worth it where stiffness and dimensional stability are required, and it should be priced at quotation rather than discovered during production.
Need an Engineering Plastic Component Machined?
DXSCNC machines drawing-based plastic components in POM, PA, PEEK, PC, PPS and similar grades, including glass-filled and wear-modified types, with the annealing and measurement condition agreed before production.
Use the model-specific machining limits when planning a part. Material, geometry, tolerance, workholding and inspection affect machine selection.
Related DXSCNC resources: Black POM Long Cylindrical Component, Common Aluminum Alloys Guide, Turn-Mill Machining and Reducing Burr Risk in CNC Turned Components.