Plating on Copper Alloys: Choosing the Finish Before the Thread Is Cut

On a steel part, a coating is often a corrosion decision made after the geometry is fixed. On a copper part it is usually a functional decision made much earlier, because the reason copper gets plated is rarely cosmetic: it is contact resistance, solderability, wear on a sliding contact, or tarnish that would change resistance over time.

That difference matters because plating adds metal to every surface it touches. A 10 µm coating grows the part by 10 µm on every side, which is 20 µm on a diameter and a measurable change on a thread flank. If the allowance is not decided when the drawing is released, the parts come back from the plater dimensionally correct in every respect except the one that matters.

Why Copper Parts Get Plated

ReasonWhat is actually being solvedFinish usually specified
Contact resistance must stay low and stableCopper oxides and tarnish raise resistance at a joint; a noble or semi-noble coating keeps it stableSilver, gold over nickel
The part must be soldered or press-fitOxide prevents wetting and increases joint resistanceTin, silver
Two parts slide or mate repeatedlyCopper and its alloys wear and gall under repeated contactNickel underlayer with silver or hard gold over it
Appearance or tarnish resistanceCopper alloys discolour in humid or sulphide-bearing airNickel, tin, anti-tarnish treatment on silver
Barrier against diffusionCopper diffuses into solder and into gold, degrading the joint over timeNickel barrier layer

Tin

Tin is the workhorse finish for copper busbars, terminals and press-fit contacts. Typical thickness runs 5–15 µm. It is cheap, it solders well, it provides a stable contact surface, and it is forgiving of imperfect surface preparation compared with silver.

The known weakness is whiskers: tin deposits can grow fine conductive filaments over time, driven by internal stress in the deposit. On a fine-pitch connector a whisker is a short circuit waiting to happen. The countermeasures are well established and they belong on the drawing rather than in the plater's discretion — a matte rather than bright deposit, a nickel underlayer to interrupt the diffusion path, control of deposit stress, and in some cases a reflow or heat treatment after plating to relieve the stress that drives growth. Where the part will run at elevated temperature or carry a high current, long-term contact resistance and thermal cycling also have to be considered, not just the initial value.

Silver

Silver gives the lowest contact resistance of the common finishes and the best resistance to arc damage, which is why switchgear contacts, busbar joints and high-current connectors are silver plated. Typical thickness is 3–10 µm, often over a thin nickel underlayer that acts as a diffusion barrier and improves wear resistance.

Two limitations are worth designing around. Silver tarnishes in sulphide-bearing atmospheres, forming a dark film that raises contact resistance at low signal levels, so an anti-tarnish treatment or a controlled storage and packaging regime is usual. And silver is soft: under repeated mating it wears through quickly unless the nickel underlayer carries the mechanical duty. In humid conditions with a DC potential, silver is also susceptible to electrochemical migration between closely spaced tracks, which is a layout concern as much as a plating one.

Nickel

Nickel is used both as an underlayer and, less often, as a final finish. As an underlayer its job is to sit between the copper and the noble coating as a diffusion barrier, to provide a hard substrate so that a soft silver or gold layer does not wear straight through to copper, and to improve corrosion resistance at pores in the top coat.

As a final finish it is hard, wear resistant and temperature resistant, and it is the right answer for a part that needs abrasion resistance rather than conductivity. The trade is contact resistance: nickel is noticeably higher than silver or tin, so where nickel is the outer layer the design needs sufficient contact force, or a thin silver or tin flash on top of it.

Gold

Gold is specified where contact stability matters more than cost: dry-circuit signals, low and stable contact resistance, and surfaces that will not oxidise over years. On a copper alloy it is essentially always applied over nickel, both because gold adheres poorly to copper and because the nickel stops copper from diffusing through the thin gold layer.

Thickness is the part that gets mis-specified. A flash of 0.05–0.2 µm is enough to protect a surface that is not mechanically worn, and it is not enough for a connector that is mated repeatedly, which needs a harder gold — alloyed with a small amount of cobalt or nickel — at a greater thickness. Where a drawing says only "gold plated", the thickness and hardness class are undetermined, and the two extremes differ in cost by an order of magnitude.

What Plating Does to Dimensions

This is where most of the practical trouble sits, and it is entirely avoidable.

FeatureWhat changesWhat to settle on the drawing
ThreadsCoating builds on the flank, tightening the fit; on a small thread a 10 µm coating removes a significant part of the clearanceWhether the thread is masked, plated, or cut undersize to allow for coating
Bores and fitsA coated bore shrinks by twice the coating thickness; a coated shaft grows by twice itThe pre-plate dimension and which tolerance the plated condition must meet
Press fitsInterference changes the assembly force and can damage the coating on assemblyWhether the fit surface is masked, and the assembly method
Sharp edgesCoating thins or builds unevenly at edges, and can be porous thereDeburr requirement before plating, since plating cannot fix a burr
Blind holes and crevicesCoverage is poor and trapped chemistry can bleed out laterWhether the feature needs plating at all, or can be masked

The working rule is that the plating allowance belongs to the machining drawing, not to a note added at the end. A part machined to nominal and then plated is out of tolerance by exactly the coating thickness, and the decision about which side of nominal to machine on has to be made before the first cut.

Choosing by Function

FunctionFinishTypical thicknessWatch for
Solderable, low cost, general purposeTin5–15 µmWhisker growth; solderability after long storage
Low and stable contact resistance, high currentSilver over nickel3–10 µm silverTarnish; wear through if the nickel is omitted
Repeated mating with wearHard gold over nickel0.5–2 µm goldCost; specify hardness class, not just thickness
Wear resistance without conductivityNickel2–5 µmHigher contact resistance; magnetic
Diffusion barrier under a noble top coatNickel underlayer1–3 µmAdhesion and coverage in recesses

Inspection

  • Thickness — measured by X-ray fluorescence on the finished part, or on a coupon plated in the same batch. Both the coating and any underlayer should be reported separately.
  • Adhesion — a bend or thermal shock test on a coupon; a coating that passes thickness but fails adhesion will fail in service at the first thermal cycle.
  • Porosity — relevant for thin noble coatings over copper, since pores become corrosion sites. Test methods are coating-specific.
  • Solderability — a wetting test where the part will be soldered, and worth repeating after storage rather than only at receipt.
  • Salt spray — useful for tin and nickel, of limited value for silver and gold, which fail by tarnish and wear rather than by chloride attack. Quoting a salt-spray hours figure for a silver coating tests something other than what the part will experience.

One copper-specific point: leaded brass machines with lead smeared across the surface, and that lead has to be removed before plating or it will cause blistering and poor adhesion. A brass part that plates badly is more often a cleaning problem than a plating bath problem.

What to Put in an RFQ

  • The finish and the thickness, with the underlayer stated separately rather than implied.
  • The tolerance that applies to the plated condition, and which dimensions are measured before and after plating.
  • Which features are masked, particularly threads, bores and press fits.
  • The base alloy, including whether it is a leaded brass, since that affects pre-treatment.
  • The functional requirement in one line — contact resistance, solderability, wear, appearance — because it often changes the finish that should have been specified.
  • Any requirement for coating thickness records, adhesion test results or first-article approval before the batch is plated.

Frequently Asked Questions

Does plating a thread change the fit?

Yes, and the effect is larger than most drawings assume. A coating of 10 µm builds on both flanks, so a thread that was cut to nominal will no longer accept a GO gauge cleanly, and on small threads the loss of clearance is a substantial fraction of the total. The usual solutions are to mask the thread, to cut it undersize to allow for the coating, or to plate before the thread is finished — and which of those is intended has to be on the drawing.

Why specify nickel under gold rather than gold directly on copper?

For two reasons. Copper diffuses through a thin gold layer over time, so the surface that was gold becomes a copper-gold mixture and loses the stable contact resistance the gold was bought for. And gold on copper adheres poorly and wears through quickly. The nickel layer stops the diffusion and provides a hard substrate, which is why essentially all functional gold on copper is gold over nickel.

Is salt spray a useful test for a silver-plated contact?

Not really. Silver fails in service by sulphide tarnish and by mechanical wear, neither of which salt spray measures, so a good salt-spray result says little about whether the contact will hold its resistance. Thickness, adhesion and a contact-resistance measurement before and after thermal cycling test the properties that actually matter for a silver contact.

Need a Plated Copper Alloy Component?

DXSCNC machines drawing-based brass and copper components — threaded fittings, adapters, contact parts, sleeves and flanged bodies — and reviews the plating allowance, masking requirement and inspection basis with the drawing before production.

Use the model-specific machining limits when planning a part. Material, geometry, tolerance, workholding and inspection affect machine selection.

Related DXSCNC resources: Copper Alloy Grade Guide, Brass CNC Turned Fittings, Threaded Components and Quality Inspection.

Request a Quote for Plated Copper Alloy Parts

Specify where coating changes acceptance

Plan the fit

On a plated bore, coating on opposite sides reduces the opening. A plated OD grows. Agree with the finishing supplier how coating builds on the functional surface and how threads or seats are masked.

Define the final inspection point

List the dimensions accepted before plating and those verified after plating. Identify gauge access, the thread gauge or mating test required, and how finished parts are protected in packing. See the brass turn-mill production example.

Request a Quote