When 45# Steel Is Not Enough: 40Cr, 42CrMo and 20CrMnTi
45# steel covers more shaft, pin and sleeve work than any other grade in a Chinese machine shop. Quenched and tempered, it delivers a usable combination of strength and toughness at a low material cost, and it machines predictably. Most drawings that call for it do not need anything else.
What follows is about the drawings that do. There are four situations in which 45# stops working, and each of them points at a different replacement rather than simply at "a stronger steel". Reading the failure mode first is what keeps a substitution from being expensive and wrong.
Four Situations Where 45# Stops Working
| Situation | What is actually failing | What the replacement has to fix |
|---|---|---|
| The section gets larger | 45# hardens at the surface but not through the core, so the core stays soft after quenching and the part has a hard shell over a weak centre. | Hardenability, not carbon. More carbon does not help a thick section; an alloying element that slows the transformation does. |
| The load goes up | Yield and ultimate strength are insufficient at the specified hardness. | Higher achievable strength at a hardness that still leaves usable toughness. |
| The load repeats or impacts | Fatigue initiation and brittle fracture under cyclic or shock loading. | Toughness and cleanliness, which usually means alloying rather than more carbon. |
| The surface must wear and the core must not | A single through-hardened grade cannot be both hard at the surface and tough underneath. | A case-hardening steel: low-carbon core, hard surface after carburising. |
The first three are problems of hardenability and toughness. The fourth is a different design entirely, and it is the one most often got wrong, because it looks like a strength problem when it is a hardness-distribution problem.
Two Different Jobs: Through-Hardening and Case-Hardening
Chinese practice divides these steels into two families by what the heat treatment is trying to achieve, and the split is the most useful thing to understand before reading a GB/T 3077 drawing.
| Quench and temper family (调质钢) | Case-hardening family (渗碳钢) | |
|---|---|---|
| Carbon level | Medium, roughly 0.30–0.50% | Low, roughly 0.15–0.25% |
| Heat treatment | Quench and high-temperature temper | Carburise, then quench and low-temperature temper |
| Resulting part | Hard and tough through the whole section | Hard, wear-resistant case over a tough, low-carbon core |
| Typical grades | 40Cr, 35CrMo, 42CrMo, 40CrNiMoA | 20Cr, 20CrMnTi, 20CrMo, 20CrNiMo |
| Typical parts | Shafts, pins, connecting rods, sleeves, high-strength bolts | Gears, spline shafts, transmission shafts, sleeves with a worn bore |
| What goes wrong if mixed up | A carburising grade used through-hardened gives a soft, low-strength part | A through-hardening grade carburised gives a brittle case over an already-hard core |
Reading the Quality Suffix: 40Cr, 40CrA, 40CrE
GB/T 3077 divides alloy structural steel into three quality classes, and the class is carried by a suffix on the grade.
- 40Cr — quality steel, the default class.
- 40CrA — high-grade quality steel, tighter on phosphorus, sulphur and other residuals. Chosen where fatigue life or toughness is critical.
- 40CrE — special-grade quality steel, tighter again. Rare outside demanding applications.
One trap is worth flagging because it catches people reading Chinese material certificates: a grade ending in RE is not a special-grade E steel. RE denotes rare-earth treatment, a deliberate addition used for inclusion control and machinability. The letter looks similar and the meaning is unrelated, and the two cannot be inferred from one another.
The Quench-and-Temper Ladder
The four grades below are usually presented as a ladder, and the ladder is real, but the step between each rung is bought with a specific property rather than with a uniform "more strength".
40Cr
The most common quench-and-temper alloy steel in Chinese practice. Chromium at around 1% raises hardenability enough to through-harden sections that 45# cannot, and it improves wear resistance. For a shaft that needs to be uniformly hard at 40 mm rather than just at the skin, 40Cr is the first answer and often the last one. Its equivalent, 41Cr4, is widely stocked in Europe, which makes substitution straightforward.
35CrMo and 42CrMo
Adding molybdenum to a chromium steel raises the tempering temperature the steel can survive, which means the part keeps its hardness after a higher-temperature temper — and a higher-temperature temper is what buys toughness. That is why 42CrMo holds up under combined high load, impact and repeated stress where 40Cr starts to run out of toughness at the hardness the design needs. 42CrMo is also the grade most often nitrided, because Mo-bearing steels resist the softening that nitriding temperatures would otherwise cause.
Machining behaviour for 42CrMo4 is covered separately on the 42CrMo4 page, including what changes when the part is machined before versus after heat treatment.
40CrNiMoA
Nickel adds toughness, especially at low temperature, and chromium and molybdenum add hardenability and temper resistance. The result is the grade used when strength, toughness, impact resistance and fatigue resistance are all required at once: highly stressed shafts, connecting rods, gearbox parts, critical fasteners. It is expensive and it is harder to machine, so it is chosen when the loading genuinely justifies it.
The Case-Hardening Ladder
20Cr
A low-carbon chromium steel. The core stays soft and tough, the carburised surface reaches a high hardness, and the chromium improves case hardenability so the hardened layer is uniform. This is the general-purpose answer for a part that needs a wear-resistant surface on a shock-resistant body.
20CrMnTi
The typical Chinese carburising gear steel. Chromium and manganese raise hardenability; titanium refines the grain, which keeps the steel from growing coarse during the long, high-temperature carburising cycle. That grain stability is the real reason it dominates gear work: it tolerates the process without losing toughness in the core.
There is no exact European equivalent. 20MnCr5 is the usual substitute and is close in carbon, manganese and chromium, but the titanium addition is what distinguishes 20CrMnTi, and the substitution should be accepted by whoever owns the drawing rather than assumed by the supplier.
Steel Groups and What the Elements Are Doing
GB/T 3077 groups its grades by alloy system, and the group name is a summary of which property was being bought.
| Group | Grades | What the elements contribute |
|---|---|---|
| Mn | 20Mn2, 40Mn2, 45Mn2 | Manganese raises strength and hardenability at low cost; the economical route to a stronger part without chromium. |
| Cr | 20Cr, 40Cr | Chromium raises hardenability, strength and wear resistance. |
| CrMo | 35CrMo, 42CrMo | Chromium for hardenability, molybdenum for temper resistance and toughness at the required hardness. |
| CrMnTi | 20CrMnTi | Chromium and manganese for hardenability, titanium to keep the grain fine through carburising. |
| CrNi | 20CrNi, 40CrNi, 12CrNi3, 20Cr2Ni4 | Nickel for toughness, particularly at low temperature, in parts where brittle fracture is the risk. |
| CrNiMo | 20CrNiMo, 30CrNiMo, 40CrNiMo, 40CrNi2Mo | The full combination: hardenability, toughness and temper resistance for the most heavily loaded parts. |
| CrNiW | 18Cr2Ni4W, 25Cr2Ni4W | Tungsten raises temper resistance and retains hardness at elevated temperature. |
Equivalents and the Risk of Substituting Them
| GB/T 3077 | Closest EN | AISI / SAE | Substitution risk |
|---|---|---|---|
| 40Cr | 41Cr4 | 5140 | Low. Widely interchangeable and stocked in both systems. |
| 35CrMo | 34CrMo4 | 4135 | Low to moderate. Check the specified hardness against the hardenability band of the substitute. |
| 42CrMo | 42CrMo4 | 4140 | Low. The most reliably interchangeable pair in this family. |
| 40CrNiMoA | 40NiCrMo6 | 4340 | Moderate. The A suffix sets tighter residuals that a general 4340 certificate may not meet. |
| 20Cr | 20Cr4 | 5120 | Low to moderate. Confirm the case depth requirement transfers. |
| 20CrMnTi | 20MnCr5 (no exact match) | — | High. The titanium grain refinement is not reproduced, and it matters in long carburising cycles. |
What Changes at the Drawing Stage
Most of the cost difference between these grades is decided before a chip is cut, and three points are worth settling at quotation rather than in production.
- Hardness and where it is measured. A hardness specified at the surface, at the core, or at a stated depth below the case are three different requirements. A single "HRC 45–50" note without a location is ambiguous on a carburised part.
- Machining before or after heat treatment. Machining in the soft state is easier and then the part moves during heat treatment; machining after heat treatment holds dimensions but costs tool life. Either way the allowance and the grinding stock have to be planned together.
- Case depth, if carburised. Case depth is a process specification, not a material one. It has to be on the drawing, and it needs to be consistent with the finishing allowance, because grinding after carburising reduces the effective case.
What to Put in an RFQ
- The exact grade including any quality suffix, and the standard version if the drawing names one.
- The heat treatment: quench and temper, carburise and harden, nitrided, or supplied in the soft state.
- The required hardness with its measurement location, and the case depth where applicable.
- Whether machining happens before or after treatment, and the grinding allowance if surfaces are to be ground.
- The section size at the hardest-working location, since hardenability is a section-size question as much as a grade question.
- Whether an equivalent EN or AISI grade is acceptable, and if so whether the substitution has been approved by the drawing owner.
Frequently Asked Questions
Is 42CrMo the same as 42CrMo4?
Yes on the grade and no on the document. 42CrMo is the Chinese designation, 42CrMo4 the European one, and their carbon, chromium and molybdenum ranges line up closely enough that the two are routinely substituted for one another. What differs is the certified hardenability band and the residual limits, so a part with a hardness requirement at depth should be verified against the certificate it actually ships with.
Can 40Cr replace 45# steel directly?
In many cases yes, and it is the usual first upgrade when 45# will not through-harden. 40Cr carries a little less carbon and roughly 1% chromium, so it hardens deeper and wears better, while achieving slightly lower maximum hardness. A drawing that depends on the top of 45#'s hardness range should be re-checked before the swap, and the change should be recorded rather than treated as an internal workshop decision.
Why use 20CrMnTi instead of a through-hardening grade for a gear?
Because a gear has two opposing requirements in one part. The tooth flank needs a hard, wear-resistant surface; the tooth root and the core need toughness to survive impact without cracking. Case hardening produces both from one low-carbon steel, whereas a through-hardened grade has to compromise between surface hardness and core toughness at a single value.
Need an Alloy Steel Component Machined?
DXSCNC machines drawing-based alloy steel components in the condition the drawing requires, including parts machined before heat treatment with finishing allowance, and parts machined after treatment where the geometry allows.
Use the model-specific machining limits when planning a part. Material, geometry, tolerance, workholding and inspection affect machine selection.
Related DXSCNC resources: Carbon Structural Steel Grades (GB/T 699), 42CrMo4 CNC Machined Parts, 45# Steel CNC Machining and Spring Steel Grades.