Technical Notes

What Does 6061-T6 Mean? Heat Treatment, Properties and CNC Machining

The number identifies the aluminum alloy. The T6 suffix identifies its heat-treated condition. Here is what happens between those two labels and why it matters on a machining drawing.

A drawing marked 6061-T6 specifies both an alloy and a temper. 6061 belongs to the heat-treatable 6xxx aluminum family, in which magnesium and silicon contribute to strengthening. T6 means the material has been solution heat-treated and artificially aged. The temper is part of the material requirement, not a cosmetic suffix.

What happens during T6 treatment?

  1. Solution heat treatment. The alloy is heated so magnesium and silicon can dissolve into the aluminum matrix. For 6061, published example schedules use temperatures around 520–535 °C. The holding time follows the product form and section thickness.
  2. Rapid cooling. The material is quenched to retain a supersaturated solid solution. Water quenching is a common route; the cooling method and rate are controlled for the product being made.
  3. Artificial aging. The quenched material is held at a lower temperature, often in the broad range of 160–180 °C for several hours. Fine magnesium–silicon-rich precipitates, often described as Mg₂Si-related phases, form and increase strength and hardness.

As one published sheet-and-coil example, a supplier describes solution treatment near 532 °C, water quenching and aging at 177 °C for eight hours. “T6” names the resulting temper; it does not prescribe one identical furnace schedule for every plate, bar, tube and extrusion.

Representative 6061-T6 properties

Illustrative room-temperature data for 6061-T6 sheet and plate
PropertyRepresentative value
Ultimate tensile strengthAbout 310 MPa
Yield strengthAbout 276 MPa
Brinell hardnessAbout 95 HB
DensityAbout 2.70 g/cm³

Values such as 290 MPa tensile and 240 MPa yield also appear in specifications for some 6061-T6 product forms. Minimum strengths change with the material standard, stock form and thickness. For procurement or inspection, use the values stated in the applicable product specification and material certificate.

Why is 6061-T6 popular for machined parts?

It combines useful strength with low weight, corrosion resistance, good anodizing response and practical machinability. It is used for fixtures, sleeves, housings, equipment parts and other components made from bar, plate or extrusion. In CNC turning, chip control still matters: ductile aluminum can produce long chips, so tooling and cutting conditions should match the geometry and stock.

Two details that affect the finished part

Residual stress and movement after machining

Rapid cooling can leave residual stress in stock. When machining removes a large amount of material from one side of a thick plate or a thin-walled shape, the part may move. Material choice, balanced stock removal, suitable clamping and a stress-relieved temper such as 6061-T651 plate can help control distortion where the design calls for it. T651 is a distinct temper and should be specified on the drawing when required.

Strength near a weld

6061 is weldable, but heat from welding can soften the heat-affected zone. A welded area therefore should be assessed using the properties of the actual welded condition. If the design needs T6-level properties after joining, the joining and any subsequent heat-treatment route need to be specified together.

What should a drawing say?

State 6061-T6, the applicable material standard and the intended stock form: bar, plate, tube or extrusion. Add any required certificate, anodizing specification and critical dimensions after finishing. For distortion-sensitive plate parts, identify whether the design calls for T651. This gives the manufacturer a clear basis for material selection, machining and inspection.

Frequently asked questions

Does T6 always mean exactly 530 °C solution treatment and 170 °C aging?

No. T6 defines a solution heat-treated and artificially aged condition. Those temperatures are useful examples, while the actual schedule is controlled for the product and specification.

Is 6061-T651 the same as 6061-T6?

Both are solution heat-treated and artificially aged. T651 includes stress relief by stretching, which is often useful when plate will be heavily machined.

Does a weld remain in the original T6 condition?

The heat-affected area can lose strength during welding. Design and inspection should use the properties of the finished welded assembly.

Related DXSCNC resources

Request a Quote

Technical references

Request a Quote