Material
7075 Aluminum CNC Machining for High-Strength Drawing-Based Parts
DXSCNC supports CNC turning and turn-mill machining for drawing-based components made from 7075 aluminum. 7075 aluminum is often selected when higher strength and lower weight are required. It is suitable for UAV parts, robotics components, precision spacers, structural adapters and other mechanical parts where strength-to-weight ratio matters.
DXSCNC is a China-based precision CNC turning and turn-mill machining supplier focused on drawing-based rotational and assembly-sensitive components. Machining range depends on the machine type and the part setup.
Typical Components
- UAV spacers and posts
- lightweight shafts
- precision collars and adapters
- turn-mill components with cross holes
- mounting components requiring higher strength
Material Designation and Equivalents
These are comparison designations, not automatic substitutions. Chemical composition, mechanical properties, delivery condition and certification requirements vary by standard and supplier, so the customer drawing and the material certificate govern the order.
| Chinese designation | GB/T 3190 7075 |
|---|---|
| European designation | EN AW-7075 |
| Werkstoff number | 3.4365 |
| Common North American comparison | UNS A97075 (7075-T6 / T651 common) |
| Japanese comparison | JIS A7075 |
| Final engineering reference | Customer drawing, applicable standard and material certificate |
Why 7075 Is a Strength Choice With Corrosion Conditions Attached
7075 (EN AW-7075, 3.4365) is a zinc-bearing alloy that reaches strengths comparable with some steels: roughly 570 MPa tensile in T6 against about 310 MPa for 6061-T6. That strength arrives with two conditions. It has lower corrosion resistance than the 6000 series, and it is not weldable by conventional processes, so a design that assumes welded joints cannot simply be switched to 7075.
The temper matters more here than on 6061, because it governs stress corrosion behaviour. In T6, 7075 is susceptible to stress corrosion cracking when a sustained tensile load acts across the short-transverse direction, which in practice means through the thickness of plate. T73 is deliberately overaged to reduce that susceptibility at a cost of roughly ten percent of the strength, and T651 is stretched to relieve residual stress without changing the temper. Which one the drawing needs depends on the load direction and the environment, and the two are not interchangeable.
Thick plate carries significant residual stress. A pocket machined into 7075 plate can close or open as the surrounding material is removed, and the distortion appears after the part has left the machine. Stress-relieved stock and a balanced machining sequence are the practical controls.
Machining Route: Residual Stress in Thick Plate
7075 machines well and the cutting data is not usually the difficulty. The difficulty is that the part is stiff only until enough material has been removed, at which point the residual stress in the plate starts to govern the geometry. A deep pocket that measures flat at the end of the finishing pass can bow overnight, and the effect is larger on thicker stock because more stress is stored in it.
The sequence therefore matters more than the cutting data. Removing material symmetrically from both faces, roughing with an allowance and letting the part rest before finishing, and avoiding a single heavy cut into a thin web are the usual controls. Where the design allows it, specifying stress-relieved plate removes most of the problem before machining starts.
Sharp internal corners deserve separate attention on this grade. A sharp corner is a stress raiser in any material, but in a high-strength alloy under sustained load in a corrosive environment it becomes the initiation point for cracking. A fillet that costs nothing to model can decide whether a part lasts.
Critical Features in 7075 Components
- thin webs and pocket floors released from stressed plate
- sharp internal corners acting as stress raisers under sustained load
- bores and bore-to-face relationships through thin walls
- fastener holes, where load transfer concentrates stress
- flatness and parallelism on pocketed faces
- surfaces left uncoated in a chloride environment
- features loaded across the plate thickness rather than in plane
Inspection Focus for 7075 Components
- dimensional and flatness check after the part has relaxed, not at the end of the cycle
- temper verification against the certificate where strength is functional
- surface condition inside machined pockets, where corrosion initiates
- coating or anodising coverage on load-bearing surfaces
- thread and fastener hole condition
- indication checks on highly stressed sections where the drawing requires them
- grain direction confirmation on parts cut from plate
What to Put in a 7075 RFQ
- temper: T6, T651 or T73, with the reason stated where strength and corrosion resistance conflict
- stock form and thickness, and the grain direction the design assumes
- service environment: chlorides, moisture, temperature
- whether a sustained tensile load acts across the plate thickness
- surface protection: anodising, conversion coating, paint or bare
- flatness and parallelism limits on machined faces
- whether stress-relieved stock is required
- first batch and repeat quantity
Machining 7075: What Actually Drives the Process
7075 cuts cleanly and holds a good finish, which makes it tempting to run like 6061 and then wonder why the part moves. The alloy is stronger and less ductile, so chips break rather than smear, but the stock carries more residual stress and the part is stiffer, which means it stores that stress until the geometry is thin enough to release it.
The practical consequence is that roughing and finishing want to be separated. Roughing removes the bulk and lets the part take its new shape; a rest period, or an intermediate stress relief where the specification allows it, lets the movement happen before the finishing cuts set the final geometry. Finishing straight after roughing in a single setup produces a part that measures correctly and changes afterwards.
Cutting needs to respect notch sensitivity. A sharp corner, a tool mark or a poorly blended fillet concentrates stress, and in 7075 those points are where cracking starts rather than where it is noticed. A finishing pass that leaves a clean, blended radius is worth more here than a marginally faster cycle.
Where 7075 Parts Go Wrong
Stress corrosion cracking is what separates 7075 from the 6000 series. A part under sustained tensile stress in a humid or chloride-bearing environment can crack through the short-transverse direction with no visible corrosion product and no measurable loss of section. The load does not have to be large; it has to be sustained. Where that combination exists, the temper, the load direction and the surface protection all have to be right at the same time.
Distortion is the second, and it is often mistaken for a machining fault. A pocketed plate part that bows after leaving the machine did not change because the cutter was wrong; it changed because removing material released stress that was already in the stock. Arguing about the finishing pass will not fix it, and a tighter flatness tolerance on the drawing will not either.
The third is a design assumption rather than a manufacturing one. 7075 is not weldable by conventional processes, so a drawing that shows a welded bracket in 7075 cannot be delivered as drawn, and moving to 6061 or 6082 is a strength decision rather than a shop-floor one. It is worth catching at quotation instead of at the welding bench.
Related DXSCNC Pages
FAQ
Can DXSCNC machine 7075 aluminum parts from customer drawings?
Yes. The quotation is built from the drawing plus the temper, and on this grade the temper is not a detail: T6, T651 and T73 differ in both strength and stress corrosion behaviour. Where a drawing states 7075 without a temper, or specifies T6 for a part that carries a sustained load in a wet environment, our team will contact you directly for clarification.
What should buyers confirm for 7075 aluminum CNC machining?
Confirm the temper, the stock form and thickness, the grain direction the design assumes, and the service environment: chlorides, moisture and temperature. Where a sustained tensile load acts across the plate thickness, that has to be stated, because it decides between T6 and T73. Also confirm the surface protection, since 7075 is rarely left bare in a corrosive environment.
Does surface treatment affect quotation?
Anodising protects the surface but does not change the stress corrosion behaviour of the alloy underneath, and it changes finished dimensions in the same way as on 6061: a coated bore shrinks and a coated shaft grows by roughly the coating thickness on the diameter. Where the part also carries a sustained load, the coating is a corrosion measure, not a substitute for the right temper.
Is 7075 aluminum the same as EN AW-7075 / 3.4365?
Yes. EN AW-7075 with Werkstoff number 3.4365 is the European designation for 7075 aluminum. 7075 is a high-strength zinc-bearing alloy with lower corrosion resistance than 6061 and it is not normally welded, so surface protection and joint design should be reviewed before machining starts.
Request a Quote
Machining ranges
7075 product photograph example
View a black anodized 7075 aluminum component with window and slot features. 7050 is listed separately as a material option; the photos show 7075 only.
View the 7075 turn-mill product